Please measure the exact size of the impact screen you wish to order in inches (Width x Height).
If you’re measuring an existing screen, avoid stretching the material while measuring. Round your measurements to the nearest ½ inch.
Example:
Width: 11 ft 3 ¾ in × Height: 9 ft 11 ⅛ in → Round to: 11 ft 4 in × 9 ft 11 in → Final size: 136″ × 119″
Before placing your order, please confirm whether your setup uses a Dual System (commercial use) or a Single Screen (home use).
The rear screen is typically permanently installed using wires or bungee cords to attach it to a wall or frame.
The front screen is attached over the rear screen using hook-and-loop fasteners, with the hook side sewn on the front screen and the loop side sewn on the rear screen.
In most cases, only the front screen needs replacement and very easily installed. The rear screen is designed for long-term use and does not need to be replaced unless significantly damaged.
Front Screen: Basic finish comes with 4-inch wide hook or loop fastener sewn along the top, left, and right edges; other finish variations may have double-sided fastener, flaps, or even skirt extension to cover the floor.
Rear Screen: Basic finish comes Matching loop or hook fastener is sewn around 3 sides (top, left, and right) with grommets placed every 1 ft for secure mounting. Different mounting variations are available using webbing loops(tabs) or fastener wing flap, instead of grommets. The bottom finish can be hemmed or a sleeve for a secure wire running through.
Custom variations are available with added labor charges.
The screen is reinforced with webbing on the top, left, and right edges.
Grommets are installed every 1 ft along the webbing for mounting.
Please check your current setup to confirm the fastener type. Most front screens use hook fasteners and rear screens use loop, but it’s important to verify.
Fastener Type : 4 inch wide tape
Choose between:
Hook (rough side)
Loop (soft side)
Standard Placement:
Hook-and-loop fastener is sewn on three sides: top, left, and right edges.
Custom Placement (Optional):
For special setups (e.g., GDR screens), you may request a custom layout.
Example: Hook on left and top edges, loop on right edge.
You can write any custom hook-and-loop placement requests in special request section when placing your order.
We charge our screen by the Width.
Please select the width of the screen you are ordering from the dropdown menu.
Example:
If your screen size is 11 ft 4 in × 9 ft 11 in, choose the range:
11 ft 1 in (133″) ~ 12 ft (144″)
If your screen size is 153″ × 120″, choose the range:
12 ft 1 in (145″) ~ 13 ft (156″)
Please enter your screen size in the format shown above. Write Width x Height in inches.
Height limit is up to 126″
Example: 136" × 119"
You may write your special request here, if any.
AdvancePRO material’s Max Height is 126″. Screen with over 126″ Height needs material extension, which cost $30
Please check this if your screen is over 126″ height.
The front screen doesn’t have mounting device like grommets, fastener wings, and webbing loops for attaching itself to the frame. Instead, it have hook/loop fasteners for attaching itself to the back screen which has matching hook/loop fastener. The back screen has mounting devices which connects to the frame using ball bungees, wires, or ropes.
Single screen has both finishing & mounting setup.
Please make sure your screen’s finishing and mounting before you place your order.
A & B. 3 side Hook or Loop type Fastener (Standard Front Screen for Double Screen System)
C. Vinyl Wrap Edge Finishing – 2.5″ black vinyl wrap + 3/4″ grommets all around (Single Screen) – $30 Customization
D. Vinyl Wrap /Loop Edge Finishing – 2.5″ black vinyl wrap +1″ loop fastener + 3/4″ grommets all around (Single Screen) – $30 Customization
E. 3 side Hook type Fastener + Grommets Finishing – 1/2″ Black vinyl wrap + 2″ Hook type Fastener + 3/4″ Grommets all around (Single Screen) – $30 Customization
F. 3 side Hook type Fastener + webbing loops (tabs) all around (Single Screen) – $50 Customization
G. Double-sided Fastener Finishing + 1″ Bottom Sleeve (Front Screen)- $30 Customization
Edge finish customization may be required depending on your mounting style. Please provide detailed specifications and photos of your current setup for reference.
If any, you may add image files or video to help us understand your current screen set up.
Please review your order options, check the price and quantity, then click the “Add to Cart” button.
Now your order is in the cart. You may check your cart by click the cart icon at the top menu.
You may order several screens with same sizes and details. If you need to place orders for different sizes or details, you need to repeat for each screens.
Shipping cost will be calculated per quantity after you enter your address in the cart. You may choose shipping options from free to Fedex express.
You can place an order without creating an account, but if you plan to order regularly, we recommend signing up to receive coupons and discounts.
